2000 Chrysler Sebring problems

Defect

IMPORT PRODUCTS IS RECALLING 30,351 FUEL FILTERS SOLD TO AND BRANDED BY THE AFFINIA GROUP AS CARQUEST P/N 86523, NAPA P/N 3523, AND WIX P/N 33523 FOR USE AS REPLACEMENT EQUIPMENT ON THE VEHICLES LISTED ABOVE. THESE FILTERS MAY DEVELOP A LEAK IN THE HOSE ASSEMBLY AND/OR CONNECTORS DUE TO IMPROPERLY ADHERED LINE CONNECTORS.

Consequence

THIS CONDITION MAY RESULT IN A VEHICLE FIRE.

Remedy

THE AFFINIA GROUP WILL NOTIFY OWNERS AND THE FILTERS WILL BE REPLACED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 1, 2009. OWNERS MAY CONTACT WIX FILTER RETURN CENTER AT 1-704-869-7411 OR IMPORT PRODUCTS AT 1-508-279-8207.

Defect

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

Consequence

DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

Remedy

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

Defect

CERTAIN AIRTEX FUEL PUMP MODULE ASSEMBLIES, P/N E7081H, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE WALL OF THE FLARED FITTING OF THE FUEL PUMP IS NOT THICK ENOUGH TO PREVENT THE MATING THREADED FITTINGS FROM BOTTOMING OUT BEFORE AN ADEQUATE SEAL IS ACHIEVED. THIS CONDITION MAY RESULT IN LEAKAGE OF FUEL AT THE CONNECTION OF THE VEHICLE FUEL LINE AND THE FUEL PUMP MODULE ASSEMBLY.

Consequence

IN THE PRESENCE OF AN IGNITION SOURCE, A FUEL LEAK COULD RESULT IN A FIRE.

Remedy

AIRTEX WILL NOTIFY OWNERS AND REPLACE THE FUEL PUMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2007. OWNERS CAN CONTACT AIRTEX AUTOMOTIVE AT 800-880-3056.

Defect

CERTAIN TIGAS FUEL PUMP MODULES MANUFACTURED BETWEEN JUNE 1 AND SEPTEMBER 24, 2006, SOLD UNDER VARIOUS BRAND NAMES AND P/NOS. THESE FUEL PUMP MODULES ARE SOLD AS AFTERMARKET FOR USE IN CERTAIN DAIMLERCHRYSLER VEHICLES LISTED ABOVE. SILICONE MATERIAL USED IN MANUFACTURE OF THE FLAPPER VALVE WAS OUT-OF-SPECIFICATION, LEADING TO EXCESS SWELL OF THE FLAPPER VALVE RESTRICTING THE FLOW OF FUEL TO THE FUEL PUMP MODULE.

Consequence

FUEL RESTRICTION COULD RESULT IN LOSS OF POWER AND/OR ENGINE STALL, POSSIBLY RESULTING IN A VEHICLE CRASH.

Remedy

TI AUTOMOTIVE WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE FUEL PUMP MODULES FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 6, 2006. OWNERS MAY CONTACT TI AUTOMOTIVE TOLL-FREE AT 1-877-461-1834.

Defect

CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Consequence

LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH.

Remedy

TRADESONIC WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING JULY 2006. OWNERS MAY CONTACT TRADESONIC AT 626-934-8884.

Defect

VEHICLE DESCRIPTION: PASSENGER VEHICLES. IF THE RUBBER BOOTS ON THE LOWER LATERAL ARM BALL JOINTS OF THE FRONT SUSPENSION WERE DAMAGED DURING ASSEMBLY, DIRT AND WATER CAN INTRUDE. ALSO, MMC HAS ADDED THE POTENTIAL OF LEAKING MOISTURE, WHICH CAN CAUSE THE BALL STUD TO CORRODE.

Consequence

THIS CONDITION COULD CAUSE THE LOWER LATERAL ARM BALL JOINT TO SEPARATE, INCREASING THE RISK OF A VEHICLE CRASH. THIS CAMPAIGN SUPERCEDES MMC'S PREVIOUS SAFETY RECALL CAMPAIGN, SEE 99V-066.

Remedy

DEALERS WILL INSPECT THE LOWER LATERAL ARM BALL JOINT FOR WEAR. BALL JOINTS THAT EXHIBIT WEAR BEYOND THE ESTABLISHED TOLERANCE WILL BE REPLACED WITH NEWLY DESIGNED LATERAL ARM BALL JOINTS. BALL JOINTS THAT ARE WITHIN THE ESTABLISHED TOLERANCE WILL BE CLEANED AND A SPECIAL SEALANT WILL BE APPLIED TO PREVENT INTRUSION OF MOISTURE.